Do you find yourself interested in answers about How to Install a Bathtub?
Installing a bathtub isn't specifically brain surgery, yet it does need strong plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bathtub with a new one is additionally a moderately hard project. If the old tub is easily accessible, the project can relocate speedily; if you need to open up a wall surface to remove the old bathtub and position the new bath tub, the job is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will certainly need a helper to leave the old bathtub and embeded in the brand-new one. Make sure you have certified yourself for the task and also are comfortable trying it. Rather than hiring a contractor to take over a halfway-completed project, it is better to think about using one prior to you begin. Possibilities are you might need a specialist plumber to make tube connections.
This short article will certainly assist you install a new bathtub in your restroom if you have actually currently bought a brand-new tub and also do not need to change the arrangement of your previous supply of water pipelines.
Your tools and material list must comprise the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you should do is detach the supply of water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The process of getting rid of the existing faucets can be rather problematic due to the limited accessibility that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Prior to moving on to fit the new faucets, contrast the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in place in between the faucet and also the sink. Safeguard the faucet in position with the supplier provided backnut. Once the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet ports. The former type ought to be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bath tub in the needed placement. The wooden boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The next objective is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the bath tub up until the level reviews level.
To set up faucets, fit all-time low of the furthest versatile faucet connector to the proper supply pipe by making a compression join; after that do the same for the various other tap.
Turn on the supply of water and inspect all joints as well as brand-new pipework for leakages and tighten them if necessary. Fill up the bathtub as well as additionally check the overflow outlet as well as the regular outlet for leakages.
Finally, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait till the bathtub has actually been utilized a minimum of once as this will resolve it into its last placement.
Getting ready for the Installation
To start with, the supporting framework provided with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is important to see to it that if the tap comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to avoid strain on the bath tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final setting.
Tiling Around the Tub
In the area where the bath satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to split an inflexible seal, creating the water to pass through the wall surface between the bathroom and also the tiling, leading to complications with dampness and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes and also cartridges, and also are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked paper or soft rope. Remember to always load the tub with water prior to sealing, to permit the activity experienced when the tub remains in usage. The sealant can fracture relatively very early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly readily available on the market. It is recommended to fit the ceramic tiles making use of waterproof or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed reading our section about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Many thanks for taking the time to read through our piece. Sharing is good. You just don't know, you might be doing someone a favor. We value reading our article about Installing A Bathtub.
Excellence? Just call!